...
The long list is constructed based on parsing the params.F90 file for settings and removing any parameters that are either case-dependent input (e.g. Hm0) or irrelevant (ships, groundwater flow, etc.). The following parameters are excluded from the long list:
Code Block |
---|
D50 # D50 grain size per grain type
D90 # D90 grain size per grain type
Hrms # Hrms wave height for instat = 0,1,2,3
Tlong # Wave group period for case instat = 1
Tm01switch # Turn off or on Tm01 or Tm-10 switch
Topt # Absolute period to optimize coefficient
Trep # Representative wave period for instat = 0,1,2,3
alfa # Angle of x-axis from East
aquiferbot # Level of uniform aquifer bottom
aquiferbotfile # Name of the aquifer bottom file
avalanching # Include avalanching (1) or exclude (0)
back # Switch for boundary at bay side, 0 = radiating boundary (Ad), 1 = reflective boundary; uu=0
bcfile # Name of spectrum file
bchwiz # Use beachwizard, 0 = beachwizard off, 1 beachwizard on, bed update off, 2 beachwiz on, bed update on. (also requires morphology == 1)
bedfricfile # Bed friction file (only valid with values of C)
bedfriction # Bed friction formulation: 'chezy','white-colebrook'
compi # Imaginary unit
depfile # Name of the input bathymetry file
dir0 # Mean wave direction (Nautical convention) for instat = 0,1,2,3
disch_loc_file # Name of discharge locations file
disch_timeseries_file # Name of discharge timeseries file
drifterfile # Name of drifter data file
dt # Computational time step, in hydrodynamic time
dthetaS_XB # The (counter-clockwise) angle in the degrees needed to rotate from the x-axis in SWAN to the x-axis pointing East
dx # Regular grid spacing in x-direction
dy # Regular grid spacing in y-direction
dzg1 # Thickness of top sediment class layers
dzg2 # Nominal thickness of variable sediment class layer
dzg3 # Thickness of bottom sediment class layers
flow # Include flow calculation (1), or exclude (0)
freewave # Switch for free wave propagation 0 = use cg (default); 1 = use sqrt(gh) in instat = 3
front # Switch for seaward flow boundary: 0 = radiating boundary(Ad), 1 = Van Dongeren, 1997
g # Gravitational acceleration
globalvars # Mnems of global output variables, not per se the same sice as nglobalvar (invalid variables, defaults)
gridform # Swicth to read in grid bathy files with 'XBeach' or 'Delft3D' format respectively
gw0 # Level initial groundwater level
gw0file # Name of initial groundwater level file
gwReturb # Reynolds number for start of turbulent flow in case of gwscheme = turbulent
gwfastsolve # Reduce full 2D non-hydrostatic solution to quasi-explicit in longshore direction
gwflow # Turn on (1) or off (0) groundwater flow module
gwheadmodel # Model to use for vertical groundwater head: 'parabolic' (default), or 'exponential'
gwhorinfil # switch to include horizontal infiltration from surface water to groundwater (default = 0)
gwnonh # Switch to turn on or off non-hydrostatic pressure for groundwater
gwscheme # Scheme for momentum equation (laminar, turbulent)
hotstartflow # Switch to hotstart flow conditions with pressure gradient balanced by wind and bed stress
instat # Wave boundary condtion type
kmax # Number of sigma layers in Quasi-3D model; kmax = 1 (default) is without vertical structure of flow and suspensions
kx # Darcy-flow permeability coefficient in x-direction [m/s]
ky # Darcy-flow permeability coefficient in y-direction [m/s]
kz # Darcy-flow permeability coefficient in z-direction [m/s]
lat # Latitude at model location for computing Coriolis
left # Switch for lateral boundary at ny+1, 'neumann' = vv computed from NSWE, 'wall' = reflective wall; vv=0
leftwave # old name for lateralwave
lwave # Include short wave forcing on NLSW equations and boundary conditions (1), or exclude (0)
maxiter # Maximum number of iterations in wave stationary
meanvars # Mnems of mean output variables (by variables)
mmpi # Number of domains in m direction (cross-shore) when manually specifying mpi domains
morfac # Morphological acceleration factor
morfacopt # Option indicating whether times should be adjusted (1) or not(0) for morfac
morphology # Include morphology (1) or exclude (0)
morstart # Start time morphology, in morphological time
morstop # Stop time morphology, in morphological time
mpiboundary # Fix mpi boundaries along y-lines ('y'), x-lines ('x'), use manual defined domains ('man') or find shortest boundary ('auto')
ncfilename # xbeach netcdf output file name
ncross # Number of output cross sections
nd # Number of computational layers in the bed
nd_var # Index of layer with variable thickness
ndischarge # Number of discharge locations
ndrifter # Number of drifers
ne_layer # Name of file containing depth of hard structure
ngd # Number of sediment classes
nglobalvar # Number of global output variables (as specified by user)
nhbreaker # Turn on or off nonhydrostatic breaker model
nmeanvar # Number of mean,min,max,var output variables
nmpi # Number of domains in n direction (alongshore) when manually specifying mpi domains
nonh # Non-hydrostatic pressure option: 0 = NSWE, 1 = NSW + non-hydrostatic pressure compensation Stelling & Zijlema, 2003
nonhspectrum # Switch between spectrum format for wave action balance of nonhydrostatic waves
npoints # Number of output point locations
npointvar # Number of point output variables
nrugauge # Number of output runup gauge locations
nship # Number of ships
nspectrumloc # Number of input spectrum locations
nspr # nspr = 1 long wave direction forced into centres of short wave bins, nspr = 0 regular long wave spreadin
ntdischarge # Length of discharge time series
nveg # Number of vegetation species
nx # Number of computiation cell corners in x-direction
ny # Number of computiation cell corners in y-direction
oldhu # Turn on / off old hu calculation
oldnyq # Turn off or on old nyquist switch
outputformat # Choice of output file format: 'netcdf', 'fortran', or 'debug'
paulrevere # Specifies tide on sea and land ('land') or two sea points ('sea') if tideloc = 2
pointtypes # Point types (0 = point, 1=rugauge)
pointvars # Mnems of point output variables (by variables)
posdwn # Bathymetry is specified positive down (1) or positive up (-1)
projection # projection string
px # Pi
q3d # Turn on (1) or off (0) quasi-3D sediment transport module
random # Random seed on (1) or off (0) for instat = 4,5,6 boundary conditions
rho # Density of water
rhoa # Air density
rhog8 # 1/8*rho*g
rhos # Solid sediment density (no pores)
right # Switch for lateral boundary at right, 0 = vv computed from NSWE, 1 = reflective wall; vv=0
rightwave # old name for lateralwave
rotate # Rotate (1) postprocess output with the rotate function.
rt # Duration of wave spectrum at offshore boundary, in morphological time
sedtrans # Include sediment transport (1) or exclude (0)
shipfile # Name of ship data file
ships # Turn on (1) or off (0) ship waves
solver # Solver used to solve the linear system, sip, or tridiag (only for 1d)
solver_maxit # Maximum number of iterations in the linear sip solver
struct # Switch for hard structures
swave # Include short waves (1), exclude short waves (0)
swrunup # Turn on (1) or off (0) short wave runup
t # Computational time, in hydrodynamic time
taper # Spin-up time of wave boundary conditions, in morphological time
thetamax # Higher directional limit (angle w.r.t computational x-axis)
thetamin # Lower directional limit (angle w.r.t computational x-axis)
thetanaut # Thetamin,thetamax in cartesian (0) or nautical convention (1)
thetanum # Coefficient determining whether upwind (1) or central scheme (0.5) is used.
tideloc # Number of corner points on which a tide time series is specified
tidetype # Switch for offfshore boundary, velocity boundary or instant water level boundary (default)
timings # Switch to turn on (1) or off (0) progress output to screen
tintc # Interval time of cross section output
tintg # Interval time of global output
tintm # Interval time of mean,var,max,min output
tintp # Interval time of point and runup gauge output
tnext # Next time point for output or wave stationary calculation, in hydrodynamic time
tscross # Name of file containing timings of cross section output
tsglobal # Name of file containing timings of global output
tsmean # Name of file containing timings of mean, max, min and var output
tspoints # Name of file containing timings of point output
tstart # Start time of output, in morphological time
tstop # Stop time of simulation, in morphological time
tunits # Units can be defined in udunits format (seconds since 1970-01-01 00:00:00.00 +1:00)
vardx # Switch for variable grid spacing: 1 = irregular spacing, 0 = regular grid spacing
vegetation # Turn on (1) or off (0) interaction of waves and flow with vegetation
vegiefile # Name of vegie species list file
vegiemapfile # Name of vegie species map file
wbcversion # Version of wave boundary conditions
wearth # Angular velocity of earth calculated as: 1/rotation_time (in hours), later changed in calculation code to rad/s
windfile # Name of file with non-stationary wind data
windth # Nautical wind direction, in case of stationary wind
windv # Wind velocity, in case of stationary wind
xfile # Name of the file containing x-coordinates of the calculation grid
xori # X-coordinate of origin of axis
xyfile # Name of the file containing (Delft3D) xy-coordinates of the calculation grid
yfile # Name of the file containing y-coordinates of the calculation grid
yori # Y-coordinate of origin of axis
zs0 # Inital water level
zs0file # Name of tide boundary condition series
zsinitfile # Name of inital condition file zs
|
Marginal sensitivity analysis
...